Testi Po Uzi Diagnostike
3 days ago - Sejoy Portable Digital Blood Pressure Test Kit - Sincerecare I/E Co. Pupil Gauge Pocket Clip Reusable Led Diagnostic Medical Penlight For. Cambridge sensors: microdot xtra, test strips, 50 strips/bottle, used to measure. Diagnostic Equipment>Cambridge Sensors Microdot Xtra Meter Test Strips, 50.
Microdot Test Strips, 50 Strips/Bottle Use with Microdot Xtra Meters Only Chemical Composition Each Microdot® strip contains the enzyme glucose dehydrogenase (Bacillus Sp.) = 1 IU and other ingredients (mediator, NAD, lysing agents etc.) = 200 µg. Test Strips When blood is added to the Microdot® strip, the chemicals within the strip react to create a tiny electrical current.
Your meter reads the current and displays your level of blood glucose. Crackfound. Performance Characteristics • The performance of Microdot® Test Strips has been evaluated both in laboratory and in clinical tests.
• Range: measurement range of the microdot® System is 1.2 to 29.2 mg/dL. • Accuracy: The accuracy of the Microdot® System was assessed by comparing blood glucose results obtained by 102 patients at one clinical centre with those obtained using a YSI 2300 laboratory Instrument. • Clark error grid analysis: 98% A region; 2% B region Correlation coefficient R = 0.977. • Range tested 45 to 472 mg/dL (2.5 to 26.2 mmol/L). Soal program linear sma dan pembahasan soal un. • Slope 0.973 y-Intercept 3.96 mg/dL (0.22 mmol/L).
• This means that the microdot® system compared well to a laboratory method. Precision: Within-Run Precision (20 replicates in 1 day) Glucose Value mmol/L CV% Bloodav 2.4 5.61 Bloodav 4.5 4.07 Bloodav 6.9 3.27 Bloodav 10.9 3.55 Bloodav 16.4 3.31 Total Precsion Control 2.5 5.42 Solution 6.5 4.96 20.6 4.89 This means that the strip to strip variation was not greater than 5.6%. Intended Use Microdot® Test Strips are used to measure glucose (sugar) in capillary whole blood outside of the body (in vitro diagnostic use). Use Microdot® Test Strips only with the Microdot® Blood Glucose Test System. Microdot® Test Strips are plasma calibrated to allow easy comparison of results with laboratory methods. Storage and Handling • Store the strips in their original vial in a cool, dry place between 50° and 86° F (10°-30° C).
Keep away from sunlight and heat • Do not refrigerate or freeze. • When you take a strip from the vial, close the cap immediately. Use the strip immediately. • Do not use Microdot® Test Strips more than 6 months after the vial is first opened. Write the discard date on the vial when you first open it.
• Check the expiry date on the vial. If the expiry date has passed do not use the strips.
• Always code the meter for each new vial of strips according to the user manual. This product is classified as a Medical Device which is regulated by the FDA. This product may have regulations or restrictions in some states.
It is the customer’s responsibility to determine and comply with all applicable federal, state or local laws.
I posted this on the Uzi board, but thought I would copy it here in case anyone here has a suggestion –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– OK, so I have a registered bolt 45 that I picked up earlier this year. Shot through a case of wolf with no issues and put it away until today. Today I get it out and purchase a couple of 100 round boxes of WWB from walmart. Nothing but trouble.
In semi, usually the bolt will just close with a light primer strike and rarely fire (maybe like 1 in 10). I checked the gap, tried the drag test with the spring removed and tried a different top cover. Nothing seemed amiss there. I begin thinking maybe it is the recoil spring is just too weak. In auto, it fires and cycles, but every 8-12 rounds it will end up with empty case jammed in the action.
It ejects and the rounds tend to land right by my feet, so that, seems like a slow cycle to me, the opposite a weak recoil spring. Anyone have any suggestion or thoughts, I would love to hear them. Especially those expierenced with the 45 ACP uzi.
Thanks for any tips or thoughts you have. Nut was good to go. I also tried two different barrels I had laying around. I am still hung up on why, with the selector in semi, it would advance with a shell and not fire and have a light strike. With the seletor in auot, it would start right up. I was thinking the drag of the semi-feet mnight be making the differenece if the spring is just borderline weak.
Still doesn't explain the 4' ejection pattern, unless, the reciol spring has failed to the point where they are actually ejecting too fast and bouncing around inside the chamber.Actually, I did have one go insde the barrel backwards (empty case) and the next bullett try to feed into it. Dan, I got a Group UZI earlier this year and was having similar problems. I finally sent the gun the Vector and they replaced the stamped feed ramp with the machined ramp that dramatically improved my UZI. I went from having like 4 (or more) stop-ages per magazine to not have any trouble at all. They have great customer service, are very reasonably priced, and do good work.